Ok. I've got a bit of spare time later this week, so I'll build up and test a board for you with the aim of having it ready before the weekend. I'll PM you shortly with payment details.
That was just in time. I was just about to post them up on ebay at a higher price! I'll send PM with details.
Just use the Contact Us button at the bottom of the page and an Admin should be able to do the honours for you.
Yes. £15 P&P should still fine. I'll PM you with contact details.
I'm still testing the board (and maybe i don't know how to use it
), so: So...aotta wrote: ↑Sun May 12, 2019 9:42 amI'm still testing the board (and maybe i don't know how to use it
- the extra ram is not showed by *ROMS but it works, and BeebAid shows correctly the slots as RAM;
- i had to reset (@+BREAK) the board once, since i got "Language?" after some time;
- i can't get AMX SuperArt Working: Roms are loaded while booting but "*pointer" is not found. Tried several *osmode options too.
Is it normal?
Thank you Ken! i've just made same test with Rom 3.31, and it works if manually loaded!KenLowe wrote: ↑Sun May 12, 2019 9:55 amSo...aotta wrote: ↑Sun May 12, 2019 9:42 amI'm still testing the board (and maybe i don't know how to use it
- the extra ram is not showed by *ROMS but it works, and BeebAid shows correctly the slots as RAM;
- i had to reset (@+BREAK) the board once, since i got "Language?" after some time;
- i can't get AMX SuperArt Working: Roms are loaded while booting but "*pointer" is not found. Tried several *osmode options too.
Is it normal?
1. Is normal. Only the 4 preconfigured banks show as RAM. I am hoping to write a utility that will allow you to specify your additional RAM banks, so that *ROMS does report these banks, but I've not done that yet.
2. Is not normal. However, it is possible that some programs may corrupt the private RAM area that stores the IBOS parameters. You can always save and restore the parameters with *CSAVE <filename> and *CLOAD <filename> to avoid having to manually reconfigure all your parameters after a reset.
3. I'm not sure about AMX SuperArt. I've got the ROMs (AMXSP & AMXSPS - I think?), but never known how to use them. I assume I also need some disk based program too? If you can give me some pointers, I can check it out
Edit 1: Think I'm actually talking about a different AMX utility called Stop Press! Anyway, if you could post up a copy of the ROMS / Disk Image, or point me to where I can download them, I can take a look.
Edit 2: I've just located and downloaded AMX SuperRom 3.41 from here and installed that to RAM bank 4. I get a valid response to *POINTER. If I do *POINTER ON followed by *ART it starts up the ART program.
Ok. I've written a small RAMSET utility which is a BASIC program that allows the user to inform Integra of any addition RAM that is installed in the system. This will adjust the reported amount of memory in the Startup message, and will adjust how the *ROMS command reports the ROM banks (the E/P flag becomes enabled). Once set, this setting will remain active until the utility is ran again, or until a Integra Reset is carried out.
Thank you, i think it'll useful! but can you give some help about how to use it? in basic it doesn't load, and *RAMSET hangs the Beeb..KenLowe wrote: ↑Sun May 12, 2019 3:23 pm
Ok. I've written a small RAMSET utility which is a BASIC program that allows the user to inform Integra of any addition RAM that is installed in the system. This will adjust the reported amount of memory in the Startup message, and will adjust how the *ROMS command reports the ROM banks (the E/P flag becomes enabled). Once set, this setting will remain active until the utility is ran again, or until a Integra Reset is carried out.
You don't have to excuse, it's really kind of you writing a tool like this!
